秒速赛车开奖最快

秒速赛车人工计划公式

The Original SHINGLE SEALER™ is a Clear Glaze Waterproofing Rejuvenating Roof Sealer Finish and Clear Shingle Sealer. The high-performance acrylic resin and special performance additives form a breathable clear sealer finish and helps to restore original color. Eliminates harmful water intrusion into and onto substrate by the sheeting off of water, thus reducing the environment for mold, mildew and fungi formation and cleansing the roof of dirt and pollution. SHINGLE SEALER™ can be used to rejuvenate, waterproof, seal, protect and beautify most any type of sloped roofing surface. Acrylic resins actually rejuvenate and promote extending the roof’s life & roofing surface.

GLOSS: Multiple coats will increase gloss.

秒速赛车免费计划

Excellent for use on Asphalt or Fiberglass Shingles and Roll Roofing to preserve, protect and waterproof the mineral granules. Protects against the premature breakdown of the tar composition (curling & cracking) by rejuvenating and waterproofing the mineral granules. The mineral granules protect the tar composition from the sun and water.

秒速赛车分析软件

For proper adhesion and penetration it is essential that the surface be properly prepared. On shingles or other granulated roofing surfaces wash all surfaces with a low pressure water and chlorine solution to remove any previous coatings, dirt, grease, and other foreign materials, especially mold, mildew and algae. Scrub, if necessary. SHINGLE SEALER™ will resist mildew growth, but will not kill mildew already on the surface! Apply only to a sound, well prepared roof surface. Roof surface must be completely dry and free of all moisture. Patch any holes, cracks, seams, etc., with a Clear Acrylic paintable caulk before applying the sealer.

Need help? Call toll free 1-800-423-7264 to speak with a waterproofing expert.

秒速赛车全天计划

Nationwide Original SHINGLE SEALER™ can be applied with a brush, roller or sprayer. Pump up sprayers can be used. Airless Sprayers may be too powerful, adjust pressure and other settings to spray a uniform amount of product without making runs, back roll with a thin nap roller cover.

秒速赛车规则

秒速赛车人工计划

STEP#1: VISUAL INSPECTION and REPLACEMENT of DAMAGED BUILDING MATERIALS

Physically inspect the surface area for missing or damaged building materials. Replace and/or repair all damaged areas. Patch any holes, cracks, seams, etc., with a Clear Acrylic paintable caulk before applying the sealer.

STEP#2: PRESSURE CLEANING

Soft wash or low pressure rinse the roof using and water and chlorine solution. Allow up-to 24 hours for roof to completely dry before applying SHINGLE SEALER™

STEP#3: SHINGLE SEALER™ APPLICATION

Apply 2 full coats of SHINGLE SEALER™ 2 - 4 hours apart, sit back and admire your freshly sealed shingle roof.

秒速赛车开奖结果预测

Standard product coverage on a smooth surface for SHINGLE SEALER™ is 250 sq. - 350 sq. ft. per gallon per coat. Some porous surfaces may require additional product. Two coats of SHINGLE SEALER™ is recommended for a longer life.

秒速赛车网上

Make sure SHINGLE SEALER™ is completely dry before proceeding with additional coats. SHINGLE SEALER™ dries in approximately 1-2 hours, but it is recommended to allow 2-4 hours between coats to allow for variations in weather and thickness. SHINGLE SEALER™ continues to cure for up to two weeks after application. Dry times are dependent upon the thickness of application, humidity and weather. Some conditions, such as low temperature, high humidity, evening and morning dew, can increase curing times.

秒速赛车开奖结果大小

Clean up all spills, tools and overspray immediately while the sealer is still wet with warm soapy water. Store unused product in its original container, tightly sealed and protect from freezing. Dispose of this product in accordance with local, state, or federal requirements.